Motor · Appliances
Sump pump, 1/3 HP class
The Zoeller M53 is listed by Zoeller as 3/10 HP, 9.7 A at 115 V. Retailers often call that class 1/3 HP. Starting amps are not on the sheet.
- Load
- Motor
| Figure | Value | How it was reached |
|---|---|---|
| Nameplate | 9.7 A at 115 V | 115 × 9.7 = 1,115.5 volt-amps. The maker did not publish watts or power factor, so runtime math treats those volt-amps as watts. That can overstate the watts and understate the hours. |
| Starting watts | Not published | The sources checked for this page do not print locked-rotor or startup watts. Pairings stay at maybe unless the running load already cannot fit. |
The pump behind this page is the Zoeller M53, the model Zoeller lists at 3/10 HP, 115 V, 60 Hz, and 9.7 A. It is the common cast-iron basement pump people mean when they search for a 1/3 HP sump pump. If your pump is a different horsepower, stop and read that nameplate.
Volts times amps is not yet watts
9.7 A × 115 V = 1,115.5 volt-amps. Zoeller does not print watts or power factor. A shaded-pole motor often has a power factor below 1, which would make real watts lower than 1,115.5. This site does not invent that power factor. Runtime pages treat 1,115.5 VA as watts, and they say the hours are then a short estimate.
The current check does not need the power factor. A station that can only supply 2.5 A cannot supply a 9.7 A nameplate. A station with a 15 A outlet and a watt rating above 1,115.5 W can be asked to run it, and still might refuse the start.
Starting amps are not on the page
Zoeller’s listing does not give locked-rotor amps. The start is a fraction of a second and it is the moment that knocks inverters offline. A 2,000 W pure-sine inverter has room for 9.7 A of running current at 120 V, as the question above shows, and that is not the same as a published start. Power Lifting and X-Boost modes on the stations in this guide are not treated as that missing start rating.
The pump only runs when the float calls for it. Zoeller does not print how many minutes per hour that is in a storm. A continuous runtime is the pessimistic case: the float stays up. A dry pit makes the number look generous. Neither one is a reason to skip the test.
Before you trust it in a storm
Plug the pump into the station in fair weather. If the station faults the moment the motor starts, the watt-hours do not matter. Keep a second pump or a way to get the water out that does not depend on this calculation. A fuel generator used as the backup belongs outside, with the exhaust away from the house.
Pairings that use this appliance
Questions people ask
Will a 2,000 W inverter run a 1/3 HP sump pump?
A 2,000 W inverter at 120 V can supply 2,000 ÷ 120 = 16.7 A if the watt rating is real power. The Zoeller M53 nameplate is 9.7 A at 115 V, which is under 16.7 A. Zoeller does not publish starting amps. Running current can fit a 2,000 W inverter and the pump can still trip it on startup. The answer is maybe until you test that pump.
Why does this page say 3/10 HP?
Zoeller's M53 product page says 3/10 HP, 115 V, and 9.7 A. US stores often sell that Mighty-Mate family as 1/3 HP. Three-tenths is 0.30 horsepower and one-third is about 0.33. This page uses Zoeller's figure and keeps the 1/3 HP name in the title so the search still lands here.
Sources
- Zoeller M53 sump pump with 25 ft cord — Zoeller