Yes · Will it run

How long will an EcoFlow RIVER 2 run a CPAP?

The RIVER 2 can power a ResMed AirSense 11. At 7 W the estimate covers more than one night. At 56.1 W it does not last until morning.

· About 3 min read

Station
300 W
Battery used
256 Wh
Answer
Yes
Electrical answer Yes

Yes, it has enough output. At ResMed's lowest lab figure the estimate covers more than one night. At the user-guide typical of 56.1 W it does not last a full night, so a heated setup may stop before morning.

The estimate

Usable watt-hours = 256 Wh × 0.85 = 217.6 Wh. The 85% figure is this site's inverter-loss assumption. It is not a lab reading for this model.

  1. 217.6 ÷ 7 = 31.1 hours (31 hours 6 minutes) at 7 W. Lower cited load.
  2. 217.6 ÷ 56.1 = 3.9 hours (3 hours 54 minutes) at 56.1 W. Higher cited load.
  3. 217.6 ÷ 73.2 = 3 hours (3 hours) at 73.2 W. Cited peak.

The two ends are the low and high figures in the sources. A single "typical" watt is not used.

Surge and current check

  • Rated output on the RIVER 2 is 300 W. X-Boost surge is 600 W. This site does not treat that higher number as motor-start headroom. X-Boost and Power Lifting are the maker's modes for a higher wattage, and the station page says what the maker allows them to run.
  • Continuous current this page will allow is 2.5 A at 120 V (rated watts ÷ volts). This appliance page does not have a nameplate amp figure, so the check is in watts.
  • Starting watts were not on the sources checked for this appliance. A station can still shut off on the first start even when the average watts look fine.

Read the RIVER 2 page and the cpap machine page for the citations behind these figures.

EcoFlow’s US product page names a CPAP as an example of an overnight load. That is their marketing sentence. It is not a medical clearance, and it does not pick a humidifier setting. The watts below are ResMed’s.

The output check

The RIVER 2 is rated 300 W, with 600 W of X-Boost surge. ResMed’s AirSense 11 user guide lists a 65 W supply, typical consumption of 56.1 W, and a peak of 73.2 W. All of those sit under 300 W. X-Boost is not required. The verdict is yes for “can it power the machine,” with the medical warning above the math.

The battery used for the hours is 256 Wh. EcoFlow’s product page also shows a 240 Wh banner for a RIVER 2 (240). If that is the unit you bought, the hours at the top are too long. Put 240 Wh in the calculator before you pack.

Which hour belongs to which setup

ResMed’s lab table lists 7 Wh in operation with no humidifier, 19 with a HumidAir 11, and 55 with a HumidAir 11 and a ClimateLineAir 11 heated tube. A watt-hour in that column, for an hour of therapy, is an average watt. The user guide’s 56.1 W typical is the high end of the range this site divides by. The 7 W figure is the low end.

A full night is about eight hours. Compare eight hours with the duration at the top of this page for the setup you sleep with. The no-humidifier end can cover more than one night on the 85% assumption. The user-guide typical cannot cover one full night on a 256 Wh pack after that same assumption. That gap is the whole point of publishing the range instead of one CPAP wattage.

Do not turn the humidifier off to chase the long number unless the person who prescribed the therapy told you that was acceptable. Stretching a battery is not a clinical instruction.

What to test

Run your machine, on your settings, from the RIVER 2’s AC outlet, for a night when a failure is only inconvenient. Note the percent left in the morning. That reading beats both ResMed documents and this formula. Keep the backup battery or plan your supplier already gave you. Jackery’s FAQ tells Jackery owners not to use those stations for medical devices. This pairing is an EcoFlow station. The medical limit does not disappear because the brand is different.

Questions people ask

Will the RIVER 2 run this load?

Yes, it has enough output. At ResMed's lowest lab figure the estimate covers more than one night. At the user-guide typical of 56.1 W it does not last a full night, so a heated setup may stop before morning.

How long is the estimate?

Using 256 Wh × 0.85: 31.1 hours (31 hours 6 minutes) at 7 W; 3.9 hours (3 hours 54 minutes) at 56.1 W; 3 hours (3 hours) at 73.2 W. Loads over the rated output are left out of this sentence.

What efficiency is in the math?

The site multiplies battery watt-hours by 0.85 before dividing by the load. That 85% is a planning assumption for inverter loss. It is shown because the starter station pages did not give a single measured AC efficiency to use instead.

Will a heated hose make it fail?

ResMed's peak of 73.2 W is still under the RIVER 2's 300 W rated output, so the station is large enough electrically. The heated-tube row on ResMed's lab table is 55 Wh per hour, and the user guide's typical is 56.1 W. Those are runtime problems, not a trip problem. Read the hours at the top for the low and high ends.

Can I use the USB-C port instead of the AC outlet?

The RIVER 2 FAQ lists USB-C at 60 W maximum. ResMed's typical figure is 56.1 W and the peak is 73.2 W, so the peak does not fit that USB-C port. Use the AC outlet and ResMed's own 65 W power supply unless ResMed has approved a DC cable for your exact machine. This page does not invent that cable.

Sources

  1. EcoFlow RIVER 2 product page, US — EcoFlow
  2. EcoFlow RIVER 2 output FAQ — EcoFlow
  3. AirSense 11 user guide, Americas — ResMed
  4. ResMed therapy-device power table — ResMed